1V1T One Pickup Wiring Harness ~ Standard Push-Pull COIL SPLIT
Click To Enlarge

1V1T Wiring Harness ~ Prewired
One Pickup Coil Split Harness
Featuring Push-Pull COIL SPLIT
1 Push Pull Volume Pot + 1 Tone Control Pot
Pre-Wired Electric Guitar Harness
Choice of Pot & Jack Style

These customized hand-wired VT harnesses work well with most One Pickup (i.e. One Humbucker) Systems. Each harness is unique and, based on order selections as well as current component stock on hand, may vary in appearance from the sample images.

This prewired harness features the following default options. Your menu selections may vary and we will wire to order.
*1 Standard Push-Pull Volume Control Pot
*1 Standard Split Shaft Tone Control Pot
*1 Standard Mylar Chiclet Tone Cap
*1 Standard Mono Style Jack
Customizable Options & Upgrades Available!

These harnesses use push-pull small volume pots (dime size / mini pots) for coil splitting and standard full-size large (quarter size) tone pots.

Both pot styles have long shafts for body mounting. If you are going through a guard or have a non-standard set-up, you may need additional nuts/washers (sold separately) or other modification. Audio Taper (“A” pot) or Linear Taper (“B” pot) styles are available. This style of pot will work with most coarse-knurled, 18-spline style knobs (sold separately).

The Coil Split Wiring incorporated into this harness allows you to split humbucker coils in half, cutting one coil out and allowing humbuckers to perform as single coils (also known as Coil Cut or Coil Tap). Four wire pickups are required for a coil split to work. Note that we do not recommend selecting a 250K pot for use with a push-pull coil tapping pot (exercise extreme discretion!). We provide the option to choose a North Coil (cuts the South and leaves only the North Coil engaged) or South Coil (cuts the North and leaves only the South engaged).

Our tone control capacitors help produce balanced bass, middle, and treble. Choose Paper in Oil (Black Bee), Sprague Orange Drop or Standard Mylar Chiclet Tone Cap as well as mfd measurements 0.1uF (usually paired with 25K pots / active pickups), 0.022uF (often paired with 250K pots), 0.033uF (used for many different set-ups, including LPs) or 0.047uF (usually used with 500K pots). 

Harness jacks work with standard cables only and jack sockets accept standard ¼” plugs. Your choice of jack style:
*Mono Jack (9mm mounting hole; tightens to your jack plate)
*Stereo Jack (9mm mounting hole; tightens to your jack plate)
*Barrel Jack (12mm mounting hole; tightens inside of guitar)
*Switchcraft Jack (10mm mounting hole; tightens to jack plate)

Installation requires soldering. Basic instructions are posted in the item images to show the solder connections needed. Please know your abilities, requirements, measurements and needs to make sure this item will work for you. We are available to answer any questions before you buy.

We wire each harness to order and offer many style and upgrade options along with typical replacements in standard and left-handed versions. We can accommodate many styles and preferences. If you don’t see what you are looking for, contact us for a custom quote.

*Push-Pull Pot Shaft Length: 18mm
*Push-Pull Pot Dimensions: 16.5mm (diameter) & 45mm (height)
*Push-Pull Pot Requirements: 10mm (hole diameter) & 28mm (depth)
*Standard Pot Shaft Length: 18mm
*Standard Pot Dimensions: 24mm (diameter) & 30mm (height)
*Standard Pot Requirements: 10mm (hole diameter) & 12mm (depth)
*Standard Mono Jack Length: 15mm (without pins)
*Standard Mono Jack Diameter (Mounting Hole Required): 9mm
*8” Insulated Wire Length
Variability is to be expected as measurements provided are approximations and based on the default options. Options selected will determine actual measurements. Ask any questions regarding options, measurements, installation, requirements, special requests, etc. prior to purchase.

*1 Prewired Guitar Wiring Harness Kit
Nothing else is included. Additional images may be provided for reference and comparison purposes only. There are no hard copy instructions or diagrams included. Basic directions are provided in the product images.

OPTIONAL ADDITIONS (Further Customize Your Harness!)
The Kill Switch Wiring Option allows you to interrupt the signal using an on-off, two-way toggle style mini-switch (~5.85mm diameter; 6mm hole required).

The Treble Bleed Volume Kit Wiring Modifier addresses loss of high-end signal when turning down your volume pot to keep more of your highs while maintaining volume adjustability. This option allows a more constant tone throughout the range of your volume pot and helps remove the dark muddiness typically experienced in the lower volume pot settings.

Add an Onboard Effects (OBFX) to expand your playing and get more nuance out of every session. Our OBFX product pages detail these circuits and what they can do for your set-up. Active circuits require power. These small (dime size / mini pots ~10mm hole) with long shaft (~18mm) body mount pots take the place of a Tone Pot (replacement pot).
*BCU (Active): Band Control Unit (Tone Shaper)
*EXP (Active): Expand to Peak Controller (Tone Expander)
*QDD2 (Active): Quadra Channel Sound Driver (Overdrive)
*QTB (Active): Quadra Tone Booster Driver (Tone Boost)
*TBX: Treble Bass Expander by Fender® (no battery req’d)
*VTC (Active): VTB/VTC Tone Expander (Tone Overdrive)

Buyers assume all risk of use; sales are only offered to those competent to safely and lawfully purchase and use items. ASK ANY QUESTIONS PRIOR TO PURCHASE. Due to the vast and varied nature of possible set-ups and user expertise, we do not provide specific information for every possible installation scenario. The provided BASIC instructions (posted in the item images, not sent as a hard copy with your order) will get you started. Please ask any questions before you buy if the posted instructions are not sufficient for your install or if you are unsure of your needs or ability to make modifications.

Note that we do not recommend installation using power tools as these can put too much force on the product and cause damage. Installation is best with moderate heat only (don’t have your iron too hot). Pay attention during install to avoid damage; components are sensitive. Excessive or prolonged heat can cause irreparable damage. This item is prewired. If your set-up requires you to disconnect the wires, be sure to take a picture or make note of the connections so you can reattach (solder!) properly. We do not recommend a clip/tie method for installation.

Inspect your order upon receipt. We will address any issues PRIOR to installation. Installation, modification, or use in any way invalidates the possibility of a return.

  • Item #: 1011

1V1T One Pickup Wiring Harness ~ Standard Push-Pull COIL SPLIT

Price: $27.95
* Marked fields are required.
Qty: *
Reviews (0) Write a Review
No Reviews. Write a Review